RCU Forums
Opening up one hole for spar carry-through reinforcing tube with sand paper wrap -
Opening up one hole for spar carry-through reinforcing tube with sand paper wrap -
0 2021/02/28 14:04:25
Nearly complete wing assembly -
Nearly complete wing assembly -
0 2021/02/21 17:07:53
Trimming excess Monokote from LE using a pulling technique -
Trimming excess Monokote from LE using a pulling technique -
0 2021/02/21 17:05:40
Wing panel framework covered -
Wing panel framework covered -
0 2021/02/21 17:04:22
Covering stacked and cutout for transparent window using template -
Covering stacked and cutout for transparent window using template -
0 2021/02/21 17:01:18
Cardboard/G-10 templates and tools -
Cardboard/G-10 templates and tools -
0 2021/02/21 16:58:50
0 2021/02/21 16:57:38
0 2021/01/03 09:05:15
Piling everything on the scale -
Piling everything on the scale -
0 2021/01/03 09:03:59
Internal components and missing here are the four flight control servos and ten hatch/assembly screws -
Internal components and missing here are the four flight control servos and ten hatch/assembly screws -
0 2021/01/03 08:53:55
0 2021/01/03 08:51:43
0 2021/01/03 08:50:44
Nesting approach of fuel line -
Nesting approach of fuel line -
0 2021/01/03 08:43:48
1/16" sheeting and hole for fuel line -
1/16" sheeting and hole for fuel line -
0 2021/01/03 08:42:16
Installation -
Installation -
0 2021/01/03 08:40:41
1/16" balsa ramp tail closeout component parts -
1/16" balsa ramp tail closeout component parts -
0 2021/01/03 08:38:28
Ply/balsa/ply center section hatch and notches to clear pushrods -
Ply/balsa/ply center section hatch and notches to clear pushrods -
0 2021/01/03 08:36:38
All hatches fit and sanded to size -
All hatches fit and sanded to size -
0 2020/11/02 17:55:50
0 2020/11/02 17:41:09
Receiver bay in fwd fuse section -
Receiver bay in fwd fuse section -
0 2020/11/02 17:39:06
Receiver hatch retention means -
Receiver hatch retention means -
0 2020/11/02 17:37:50
1/64" ply cuts well with scissors -
1/64" ply cuts well with scissors -
0 2020/11/02 17:35:50
0 2020/11/02 17:35:18
Hatch fabrication - balsa/ply laminates
Hatch fabrication - balsa/ply laminates
0 2020/11/02 17:33:43
Turned down some 4-40 aluminum hex standoffs on the drill press for center section hatch retention -
Turned down some 4-40 aluminum hex standoffs on the drill press for center section hatch retention -
0 2020/11/02 17:30:47
Showing collective deflections for all surfaces after commanding folding sequence; note rotation should be counterclockwise -
Showing collective deflections for all surfaces after commanding folding sequence; note rotation should be counterclockwise -
0 2020/11/02 17:25:06
Roll right, pitch up response (red arrow shows direction of fwd flight)
Roll right, pitch up response (red arrow shows direction of fwd flight)
0 2020/11/02 17:22:14
0 2020/11/02 17:16:32
Roll right, pitch up commanded -
Roll right, pitch up commanded -
0 2020/11/02 17:15:31
0 2020/11/02 17:10:40
Switching to cable on the release system allows more linear-like action and less side-load, binding than rigid music wire attempt earlier -
Switching to cable on the release system allows more linear-like action and less side-load, binding than rigid music wire attempt earlier -
0 2020/11/02 17:05:54
ID labels for servo leads at receiver -
ID labels for servo leads at receiver -
0 2020/09/22 17:35:51
Triangle stock added to corners of inside servo mounts -
Triangle stock added to corners of inside servo mounts -
0 2020/09/22 17:32:43
0 2020/09/22 17:31:10
Some allowance and fitting to clear floor retention doublers of two of the mounts -
Some allowance and fitting to clear floor retention doublers of two of the mounts -
0 2020/09/22 17:26:21
0 2020/09/22 17:24:15
0 2020/09/21 17:37:29
Ends are beveled on four to clear connector holes in center section floor -
Ends are beveled on four to clear connector holes in center section floor -
0 2020/09/21 17:32:10
Pins and endplate patterns removed -
Pins and endplate patterns removed -
0 2020/09/21 17:29:57
Permagrit sanding tool finishes slot -
Permagrit sanding tool finishes slot -
0 2020/09/21 17:22:14
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.